Hilti DCG 230-D Betriebsanleitung PDF herunterladen (Seite 32)

chitect, or person in charge of the building project

before beginning the work.

WARNING

The electric supply voltage must comply with the in-

formation given on the type identification plate on the

power tool. 230 V power tools may also be connected

to a 220 V supply.

WARNING

Always use the side handle with the power tool (use

the hoop handle as an option).

CAUTION

Use clamps or a vice to hold the workpiece securely.

WARNING

Cutting or grinding may cause splintering of the material.

Wear eye protection.

CAUTION

Breathing protection must be worn if the power tool

is used without a dust removal system for work that

creates dust.

WARNING

Avoid touching rotating parts. Switch the power tool

on only after bringing it into position at the workpiece.

Touching rotating parts, especially rotating insert tools,

may lead to injury.

CAUTION

The insert tool may get hot during use. Wear protective

gloves when changing insert tools.

CAUTION

In accordance with the applications for which it is de-

signed, the power tool produces a high torque. Always

use the side handle and hold the power tool with both

hands. The user must be prepared for sudden sticking

and stalling of the insert tool.

CAUTION

Working on the material may cause it to splinter. Wear

eye protection and protective gloves. Wear breathing

protection if no dust removal system is used. Splin-

tering material presents a risk of injury to the eyes and

body.

WARNING

Reduce the load on the power tool by avoiding tilt-

ing the disc in the kerf when cutting. The disc may

otherwise break, or the power tool may kick back or stall.

CAUTION

Improve the blood circulation in your fingers by re-

laxing your hands and exercising your fingers during

breaks between working.

WARNING

Keep inflammable materials away from the working

area.

7.1 Adjusting the grip 8

WARNING

Do not attempt tp adjust the position of the grip while

the tool is running. Check to ensure that the grip is

engaged in one of the three possible positions.

To allow the power tool to be used comfortably in all

positions, the grip can be pivoted through 90° to the left

and the right.

1. Disconnect the supply cord plug from the power

outlet.

2. Release the locking lever by pulling it back.

3. Pivot the grip to the left or right as far as it will go.

4. Secure the grip in position by closing the locking

lever.

NOTE The power tool cannot be switched on as

long as the grip is not locked in one of the three

possible positions.

7.2 Cutting

When cutting, apply moderate feed pressure and do not

tilt the power tool or, respectively, the cutting disc (hold

at approx. 90° to the surface being cut). For best results,

start cutting at the smallest cross section when cutting

profiles and square tube.

7.3 Rough grinding

CAUTION

Never use abrasive cutting discs for grinding.

Best results are obtained when the disc maintains an

angle of 5° to 30° with the working surface when grinding.

Move the power tool to and fro while applying moderate

pressure. This will avoid overheating and discoloration of

the workpiece and ensure an even surface finish.

7.4 Switching on / off

7.4.1 Switching on

1. Plug the supply cord into the power outlet.

2. Slide the on / off switch forward and then press it as

far as it will go.

In this way, the hand is closed around the power

tool, which ensures optimum safety while working.

7.4.2 Switching off

Release the on / off switch.

7.5 Restart interlock

NOTE

If the power tool is unplugged from the electric supply

while the on / off switch is pressed and subsequently

plugged back into the electric supply, the power tool will

not restart.

Printed: 20.11.2013 | Doc-Nr: PUB / 5069494 / 000 / 02

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 ... 259 260

Hilti DCG 230-D Betriebsanleitung Seite 32

Kommentare zu diesen Handbüchern